# hinv -vm
Location: /hw/module/001c01/node
IP34 Board: barcode NEY977     part 030-1707-005 rev -A
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode NEE020     part 030-1932-001 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODY Board: barcode NEJ116     part 030-1726-005 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode NEY977     part 030-1707-005 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode NEY977     part 030-1707-005 rev -A
1 800 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 2.2
FPU: MIPS R16010 Floating Point Chip Revision: 2.2
CPU 0 at Module 001c01/Slot 0/Slice A: 800 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.2. Scache: Size 4 MB Speed 400 Mhz  Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 4: Version IEEE1394 SBP2
Integral SCSI controller 2: Version LS1030, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Tape drive: unit 4 on SCSI controller 0: DAT
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 4 on SCSI controller 1
Integral SCSI controller 3: Version LS1030, low voltage differential
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A4, number 1
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 1
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 1
PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 2
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 3
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 3
PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.187
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB controller: type OHCI
USB Human Interface Device: device id 0 type mouse
USB Human Interface Device: device id 0 type keyboard
USB Human Interface Device: device id 1 type mouse
USB controller: type OHCI

# gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1920x1088
BUZZ version B.2
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: NEC 26489
Channel 0:
Origin = (0,0)
Video Output: 1920 pixels, 1080 lines, 72.00Hz (1920x1080_72)
% su
# ls /dev/scsi
sc0d1l0  sc0d4l0  sc1d4l0
# scsicontrol -i sc0d1l0
sc0d1l0:  Disk          FUJITSU MAW3073NP       0104
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
# scsicontrol -i sc0d4l0
sc0d4l0:  Tape          SONY    SDT-10000       0200
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  16bit synch
Device is  not ready

# scsicontrol -i sc1d4l0
sc1d4l0:  CD-ROM        HP      DVD-ROM 305     1.01
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch
Device is  not ready

# hinv -vm
Location: /hw/module/001c01/node
IP34 Board: barcode MRR478     part 030-1707-003 rev -H
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode NPK566     part 030-2023-001 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODY Board: barcode MXH333     part 030-1726-005 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MRR478     part 030-1707-003 rev -H
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MRR478     part 030-1707-003 rev -H
1 900 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
CPU 0 at Module 001c01/Slot 0/Slice A: 900 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 3.0. Scache: Size 8 MB Speed 450 Mhz  Tap 0xb
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Tape drive: unit 4 on SCSI controller 0: DAT
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 4 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version MAD revision 1, number 1
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)

# gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1920x1168
BUZZ version B.2
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Dual Channel Display option
Monitor 1 type: Unknown         Monitor 2 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1920 pixels, 1154 lines, 59.99Hz (1920x1154_60)
